Amiga Plus 1995 #2/Amiga Plus CD - 1995 - No. 2.iso/internet/faq/englisch/electricalwiring

Text File | 1995-04-11 | 97.3 KB | 2,174 lines

Archive-name: electrical-wiring/part1
Last-modified: Mon Nov 14 01:10:37 EST 1994

        Frequently Asked Questions on Electrical Wiring

                        Copyright 1991, 1992, 1993
        Steven Bellovin ([e-mail])
        Chris Lewis ([e-mail])

        Redistribution for profit, or in altered content/format
        prohibited without permission of the authors.  Any other
        redistribution must include this copyright notice and
        attribution.

        Comments to (automatic if you reply to this article):
            [e-mail]

The latest FAQ can always be obtained from:

    ftp://rtfm.mit.edu/pub/usenet/news.answers/electrical-wiring/part[1-2]

This FAQ is formatted as a digest.  Most news readers can
skip from one question to the next by pressing ^G.

Answers to many other topics related to houses can be obtained from
the misc.consumers.house archive; send an empty piece of mail to
[e-mail] for information.

Changes to previous issue marked with "|" in left column.  Watch
particularly for "NEW" in the Questions list for new or substantively
changed answers.  "g^|" will get you to the changed sections quickly
in most newsreaders.

------------------------------
Subject: Questions answered in this FAQ

    Introduction/Disclaimers
    What is the NEC?  Where can I get a copy?
    What is the CEC?  Where can I get a copy?
    Can I do my own wiring?  Extra pointers?
    What do I need in the way of tools?
    What is UL listing?
    What is CSA approval?
    What impact does NAFTA have on wiring standards and approvals?
|    Are there any cheaper, easier to read books on wiring?
    Inspections how and what?  Why should I get my wiring inspected?
    My house doesn't meet some of these rules and regulations.
    A word on voltages: 110/115/117/120/125/220/240
    What does an electrical service look like?
    What is a circuit?
    "grounding" versus "grounded" versus "neutral".
    What does a fuse or breaker do?  What are the differences?
    Breakers?  Can't I use fuses?
    What size wire should I use?
    Where do these numbers come from?
    What does "14-2" mean?
    What is a "wirenut"/"marrette"/"marr connector".  How are they used?
    What is a GFI/GFCI?
    Where should GFCIs be used?
    Where shouldn't I use a GFCI?
    What is the difference between a GFCI outlet and a GFCI breaker?
    What's the purpose of the ground prong on an outlet, then?
    Why is one prong wider than the other?  Polarization
    How do I convert two prong receptacles to three prong?
    Surges, spikes, zaps, grounding and your electronics
    Are you sure about GFCIs and ungrounded outlets?
        Should the test button work?
    What kind of outlets do I need in a kitchen?
    Where must outlets and switches be in bathrooms?
    General outlet placement rules/line capacities
    What is Romex/NM/NMD?  What is BX?  When should I use each?
    Should I use plastic or metal boxes?
    Junction box positioning?
    Can I install a replacement fixture?
    Noisy fluorescent fixtures, what do I do?
|    Noisy lights with dimmer switches, what do I do? (NEW)
    What does it mean when the lights brighten when a motor starts?
    What is 3 phase power?  Should I use it?  Can I get it in my house?
    Is it better to run motors at 110 or 220?
    What is this nonsense about 3HP on 110V 15A circuits?
    How should I wire my shop?
    Underground wiring
    Doorbell/telephone/cable other service wiring hints
    Aluminum wiring
    I'm buying a house!  What should I do?
    What is this weird stuff?  Old style wiring
    Where do I buy stuff?
    Copper wire characteristics table
|    Smoke detector guidelines (NEW)

------------------------------
Subject: Introduction/Disclaimers

    Although we've done a fair bit of wiring, we are not
    electricians, and we cannot be responsible for what you do.  If
    you're at all uncertain about what is correct or safe, *don't
    do it*.  Contact someone qualified -- a licensed electrician,
    or your local electrical inspector.  Electricity is no joke;
    mistakes can result in shocks, fires, or electrocution.

    Furthermore, our discussion is based on the U.S. National
    Electrical Code (NEC) and the Canadian Electrical code (CEC).
    To the best of our abilities, we have confirmed every detail
    with the electrical code, but we don't quote sections
    simply to keep this thing readable.  If you think we're wrong,
    we invite you to correct us, but please - quote references!

    The NEC and the CEC do not, in and of themselves, have the
    force of law.  Many municipalities adopt it en toto.  Others,
    however, do not.  Check your with your local building
    department (and <provincial> Hydro Inspection Offices in
    Canada) to find out what applies in your area.  Also,
    your local electrical utility may also have special requirements
    for electrical service installation.  Bear in mind, too, that
    we say here applies primarily to ordinary single-family
    residences.  Multi-family dwellings, mobile homes, commercial
    establishments, etc., are sometimes governed by different
    rules.

    Also note that, contrary to popular belief in the U.S. (and in
    some parts of Canada), Canada is not a wholly-owned subsidiary
    of the U.S.  Consequently, the NEC does not apply in Canada.
    Lots of things are the same, including voltages, line
    frequencies, and the laws of physics.  But there are a number
    of crucial differences in the regulations.  Where we can, we've
    noted them, flagging the relevant passages with ``NEC'' or
    ``CEC''.

    Remember that the CEC and NEC are minimal standards.  It is often
    smart to go beyond their minimal requirements.

------------------------------
Subject: What is the NEC?  Where can I get a copy?

    The NEC is a model electrical code devised and published by the
    National Fire Protection Association, an insurance industry group.
    It's revised every three years.  The 1993 version has been released.
    You can buy a copy at a decent bookstore, or by calling them directly
    at 800-344-3555.  The code exists in several versions.  There's the
    full text, which is fairly incomprehensible.  There's an abridged
    edition, which has only the sections likely to apply to most houses.
    And there's the NEC Handbook, which contains the ``authorized
    commentary'' on the code, as well as the full text.  That's the
    recommended version.  Unfortunately, there's no handbook for
    the abridged edition.  And the full handbook is expensive --
    US$65 plus shipping and handling.

------------------------------
Subject: What is the CEC?  Where can I get a copy?

    The Canadian Standards Association is an organization made up
    of various government agencies, power utilities, insurance
    companies, electrical manufacturers and other organizations.
    The CSA publishes CSA Standard C22.1 which is updated every two
    or three years.  Each province adopts, with some amendments,
    this standard and publishes a province-specific code book.
    Since each province publishes its own slightly modified
    standard, it would be somewhat confusing to obtain the CSA
    standard itself.  In this FAQ, "CEC" really means the
    appropriate provincial standard.  In particular, this FAQ is
    derived from the Ontario Hydro Electrical Safety Code, 20th
    edition (1990).  Which is in turn based on CSA C22.1-1990 (16th
    edition).  While differences exist between the provinces, an
    attempt has been made to avoid specific-to-Ontario detail.

    The appropriate provincial code can be obtained from electrical
    inspection offices of your provincial power authority.  In
    Ontario, it's Ontario Hydro.  The Ontario Hydro book isn't
    overly fat.  It's about C$25, and includes mailed updates.  I
    hear that these standards are somewhat easier to read than the
    equivalent NEC publications.

    Don't bother asking in Quebec - DIY wiring is banned throughout
    the province.

------------------------------
Subject: Can I do my own wiring?  Extra pointers?

    In most places, homeowners are allowed to do their own wiring.
    In some, they're not.  Check with your local electrical
    inspector.  Most places won't permit you to do wiring on other's
    homes for money without a license.  Nor are you permitted to do
    wiring in "commercial" buildings.  Multiple dwellings (eg: duplexes)
    are usually considered "semi-commercial" or "commercial".  However,
    many jurisdictions will permit you to work on semi-commercial
    wiring if you're supervised by a licensed electrician - if you can
    find one willing to supervise.

    If you do your own wiring, an important point:

    Do it NEAT and WELL!  What you really want to aim for is a better
    job than an electrician will do.  After all, it's your own home,
    and it's you or your family that might get killed if you make
    a mistake.  An electrician has time pressures, has the skills
    and knows the tricks of the trade to do a fast, safe job.
    In this FAQ we've consciously given a few recommendations that
    are in excess of code, because we feel that it's reasonable,
    and will impress the inspector.

    The inspector will know that you're an amateur.  You have to
    earn his trust.  The best way of doing this is to spend your
    time doing as neat a job as possible.  Don't cut corners.
    Exceed specifications.  Otherwise, the inspector may get extremely
    picky and fault you on the slightest transgressions.

    Don't try to hide anything from the inspector.

    Use the proper tools.  Ie: don't use a bread knife to strip
    wires, or twist wires with your fingers.  The inspector
    won't like it, and the results won't be that safe.  And it
    takes longer.  And you're more likely to stick a hunk of
    12ga wire through your hand that way.

    Don't handle house wire when it's very cold (eg: below -10C
    or 16F).  Thermoplastic house wire, particularly older types
    become very brittle.

------------------------------
Subject: What do I need in the way of tools?

    First, there's the obvious -- a hammer, a drill, a few
    screwdrivers, both straight and Phillips-head.  If you're
    lucky enough to live in Canada (or find a source of CSA-approved
    devices) you need Robertson ("square recess") screwdrivers
    (#1 and #2) instead of phillips.

    For drilling a few holes, a 3/4" or 1" spade bit and 1/4" or
    3/8" electric drill will do.  If you're doing a lot, or
    are working with elderly lumber, we recommend a 1/2" drill
    (right-angle drills are wonderful.  Can be rented) and
    3/4" or 1" screw-point auger drill bits.  These bits pull
    you through, so they're much faster and less fatiguing, even
    in 90 year old hardwood timbers.

    Screw-driver bits are useful for drills, expecially if you
    install your electrical boxes using screws (drywall screws
    work well).

    For stripping wire, use a real wire stripper, not a knife or
    ordinary wire cutters.  Don't buy the $3 K-mart "combo stripper,
    crimper and bottle opener" types.  You should expect to pay
    $15 to $20 for a good "plier-type" pair.  It will have sized
    stripping holes, and won't nick or grab the wire - it should
    be easy to strip wire with it.  One model has a small hole in the
    blade for forming exact wire loops for screw terminals.  There
    are fancier types (autostrip/cut), but they generally aren't
    necessary, and pros usually don't use them.

    A pair of diagonal side cutter pliers are useful for clipping ends
    in constricted places.  Don't use these for stripping wire.

    You will need linesman pliers for twisting wires for wire nuts.

    You should have a pair of needle-nose pliers for fiddling
    inside boxes and closing loops, but it's better to form wire
    loops with a "loop former hole" on your wire stripper - more
    accurate.

    If you're using non-metallic cable, get a cable stripper for
    removing the sheath.  Or, do what some pros do, they nick the
    end of the sheath, grab the ground wire with a pair of pliers,
    and simply rip the sheath back using the ground wire as a
    "zipper", and cut the sheath off.  You shouldn't try to strip
    the sheath with a knife point, because it's too easy to
    slash the insulation on the conductors.  Apparently Stanley
    utility knives fitted with linoleum cutters (hooked blades)
    can be used to strip sheath, but there is still the possibility
    that you'll gouge the conductors.

    For any substantial amount of work with armored cable, it's well
    worth your while to invest in a rotary cable splitter (~US$ 18).
    Hack saws are tricky to use without cutting into the wire
    or the insulation.

    Three-prong outlet testers are a quick check for properly-wired
    outlets.  About $6.  Multimeters tell you more, but are a lot more
    expensive, and probably not worth it for most people.  A simple
    voltage sensor, which can detect potential through an insulated
    wire not supplying any devices, is extremely helpful; they cost
    about US$ 10 at Radio Shack.

    You should have a voltage detector - to check that the wires are
    dead before doing work on them.  Neon-bulb version are cheap ($2-3)
    and work well.  If you get more serious, a "audible alarm" type is
    good for tracing circuits without a helper.  (Though I've been known
    to lock the drill on, and hit breakers until the scream stops ;-)

    For running wires through existing walls, you need fish tape.
    Often, two tapes are needed, though sometimes, a bent hanger or
    a length of thin chain will suffice.  Fish tapes can be rented.

    Electrical tape.  Lots of it ;-)  Seriously, a good and competent
    wiring job will need very little tape.  The tape is useful for
    wrapping dicy insulation in repair work.  Another use is to wrap
    around the body of outlets and switches to cover the termination
    screws - I don't do this, but drywall contractors prefer it (to
    prevent explosions when the drywall knife collides with a live outlet
    that has no cover plate).

------------------------------
Subject: What is UL listing?

    The UL stands for "Underwriters Laboratory".  It used to be
    an Insurance Industry organization, but now it is independent
    and non-profit.  It tests electrical components and equipment
    for potential hazards.  When something is UL-listed, that means
    that the UL has tested the device, and it meets their requirements
    for safety - ie: fire or shock hazard.  It doesn't necessarily
    mean that the device actually does what it's supposed to, just
    that it probably won't kill you.

    The UL does not have power of law in the U.S. -- you are
    permitted to buy and install non-UL-listed devices.  However,
    insurance policies sometimes have clauses in them that will
    limit their liability in case of a claim made in response to
    the failure of a non-UL-listed device.  Furthermore, in
    many situations the NEC will require that a wiring component
    used for a specific purpose is UL-listed for that purpose.
    Indirectly, this means that certain parts of your wiring
    must be UL-listed before an inspector will approve it and/or
    occupancy permits issued.

------------------------------
Subject: What is CSA approval?

    Every electrical device or component must be certified by the
    Canadian Standards Association (or recognized equivalent) before
    it can be sold in Canada.  Implicit in this is that all wiring
    must be done with CSA-approved materials.  They perform testing
    similar to the UL (a bit more stringent), except that CSA (or
    recognized equivalent) approval is required by law.

    Again, like the UL, if a fire was caused by non-CSA-approved
    equipment, your insurance company may not have to pay the
    claim.

    Note: strictly speaking, there usually is a legal way around
    the lack of a CSA sticker.  In some cases (eg: Ontario), a
    local hydro inspection prior to purchase, or prior to use, is
    acceptable.  The hydro inspector will affix a "hydro sticker"
    to the unit, which is as good as CSA approval.  But it costs
    money - last I knew, $75 per unit inspected.

    ULC (Underwriters Laboratory of Canada) is an independent
    organization that, amongst other things, undertakes the
    quarterly inspection of manufacturer's to ensure continued
    compliance of UL Listed/Recognized products to Agency reports
    and safety standards. This work is done under contract to UL
    Inc (Follow-up Services Division). They are not a branch or
    subsidiary of UL.

------------------------------
Subject: What impact does NAFTA have on wiring standards and approvals?

    The North America Free Trade Agreement came into effect on
    January 1st, 1994.  NAFTA attempts to bring down trade barriers
    between Mexico, Canada and the USA.  One of the "barriers" has
    been that of approval of material.  As of January first, CSA
    approval of a device is legally considered equivalent to UL
    approval in the USA.  Conversely, UL is now accepted as
    equivalent to CSA approval in Canada.  Theoretically, this
    means that devices marked only with UL approval are acceptable
    in the CEC, and conversely CSA approval by itself of a device
    is accepted by the NEC.  This allows much freer trade in
    electrical materials between the two countries.

    This doesn't affect the electrical codes themselves, so the
    differences in practice between the NEC and CEC will remain.
    It is also my understanding that bilateral acceptance of
    "approval" will only apply when the standards applied are
    reasonably the same.  As an example, a cable approved by the
    NEC for a given purpose may not be acceptable by the CEC for
    the same purpose if the standards requirements are different.
    Eg: "NMD" ("non-metallic, damp") cable is usually required for
    residences in Canada.  "NM" cable ("non-metallic, not damp
    locations) which is used in the same situations in the US,
    would probably not be acceptable in Canada.  Also,
    municipalities can add additional requirements on top of the
    CEC, as they can in the US over the NEC.

    Thus, Canadians will probably start seeing UL-only approved
    materials in stores, and Americans the same regarding
    CSA-only.  But some differences will remain.  When in doubt on
    major items, consult an inspector.  At least in Canada, the
    fact that the material is available in a store usually means
    that it's okay to install.

------------------------------
Subject: Are there any cheaper, easier to read books on wiring?

    USA: The following three books were suggested by our readers

        Residential Wiring
        by Jeff Markell,
        Craftsman Books,
        Carlsbad CA for $18.25. ISBN 0-934041-19-9.

        Practical Electrical Wiring
        Residential, Farm and Industrial,  Based on the National
        Electrical Code    ANSI/NFPA 70
        Herbert P. Richter and W. Creighton Schwan
        McGraw-Hill Book Co.

        Wiring Simplified
        H. P. Richter and W. C. Schwan
        Park Publishing Co.

|        The Electrician's Toolbox Manual
|        Rex Miller
|        Prentice Hall (ARCO) 1989
|        ISBN 0-13-247701-7 $11.00

Thanks again for your good efforts.


    Try to make sure that the book is based on the latest NEC
    revision.  Which is currently 1993.

    Canada: P.S. Knight authors and publishes a book called
    "Electrical Code Simplified".  There appears to be a version
    published specific to each province, and is very tied into the
    appropriate provincial code.  It focuses on residential wiring,
    and is indispensible for Canadian DIY'ers.  It is better to get
    this book than the CEC unless you do a lot of wiring (or answer
    questions on the net ;-).

    It is updated each time the provincial codes are.  This book is
    available at all DIY and hardware stores for less than C$10.

------------------------------
Subject: Inspections how and what?  Why should I get my wiring inspected?

    Most jurisdictions require that you obtain a permit and
    inspections of any wiring that is done.  Amongst other more
    mundane bureaucratic reasons (like insurance companies not
    liking to have to pay claims), a permit and inspections
    provides some assurance that you, your family, your neighbors
    or subsequent owners of your home don't get killed or lose
    their homes one night due to a sloppy wiring job.

    Most jurisdictions have the power to order you to vacate your
    home, or order you to tear out any wiring done without a
    permit.  California, for instance, is particularly nasty about
    this.

    If fire starts in your home, and un-inspected wiring is at
    fault, insurance companies will often refuse to pay the damage
    claims.

    In general, the process goes like this:
        - you apply to your local inspections office or building
          department for a permit.  You should have a sketch or
          detailed drawing of what you plan on doing.  This is
          a good time to ask questions on any things you're not
          sure of.  If you're doing major work, they may impose
          special conditions on you, require loading
          calculations and ask other questions.  At this point
          they will tell you which inspections you will need.
        - If you're installing a main panel, you will need to
          have the panel and service connections inspected
          before your power utility will provide a connection.
          This is sometimes done by the local power authority
          rather than the usual inspectors.
        - After installing the boxes and wiring, but before
          the insulation/walls go up, you will need a
          "rough-in" inspection.
        - After the walls are up, and the wiring is complete,
          you will need a "final inspection".

------------------------------
Subject: My house doesn't meet some of these rules and regulations.
    Do I have to upgrade?

    In general, there is no requirement to upgrade older dwellings,
    though there are some exceptions (ie: smoke detectors in some
    cases).  However, any new work must be done according to the
    latest electrical code.  Also, if you do ``major'' work, you
    may be required to upgrade certain existing portions or all
    of your system.  Check with your local electrical inspector.

------------------------------
Subject: A word on voltages: 110/115/117/120/125/220/240

    One thing where things might get a bit confusing is the
    different numbers people bandy about for the voltage of
    a circuit.  One person might talk about 110V, another 117V
    or another 120V.  These are all, in fact, exactly the same
    thing...  In North America the utility companies are required
    to supply a split-phase 240 volt (+-5%) feed to your house.
    This works out as two 120V +- 5% legs.  Additionally, since there
    are resistive voltage drops in the house wiring, it's not
    unreasonable to find 120V has dropped to 110V or 240V has dropped
    to 220V by the time the power reaches a wall outlet.  Especially
    at the end of an extension cord or long circuit run.  For a number
    of reasons, some historical, some simple personal orneryness,
    different people choose call them by slightly different numbers.
    This FAQ has chosen to be consistent with calling them "110V" and
    "220V", except when actually saying what the measured voltage will
    be.  Confusing?  A bit.  Just ignore it.

    One thing that might make this a little more understandable
    is that the nameplates on equipment ofen show the lower (ie: 110V
    instead of 120V) value.  What this implies is that the device
    is designed to operate properly when the voltage drops that
    low.

    208V is *not* the same as 240V.  208V is the voltage between
    phases of a 3-phase "Y" circuit that is 120V from neutral to any
    hot.   480V is the voltage between phases of a 3-phase "Y"
    circuit that's 277V from hot to neutral.

    In keeping with 110V versus 120V strangeness, motors intended
    to run on 480V three phase are often labelled as 440V...

------------------------------
Subject: What does an electrical service look like?

    There are logically four wires involved with supplying the
    main panel with power.  Three of them will come from the utility
    pole, and a fourth (bare) wire comes from elsewhere.

     The bare wire is connected to one or more long metal bars pounded
     into the ground, or to a wire buried in the foundation, or sometimes
     to the water supply pipe (has to be metal, continuous to where
    the main water pipe entering the house.  Watch out for galvanic
    action conductivity "breaks" (often between copper and iron pipe).
    This is the "grounding conductor".  It is there to make sure that
    the third prong on your outlets is connected to ground.  This wire
    normally carries no current.

    One of the other wires will be white (or black with white or
    yellow stripes, or sometimes simply black).  It is the neutral wire.
    It is connected to the "centre tap" (CEC; "center tap" in the
    NEC ;-) of the distribution transformer supplying the power.  It
    is connected to the grounding conductor in only one place (often
    inside the panel).  The neutral and ground should not be connected
    anywhere else.  Otherwise, weird and/or dangerous things may happen.

    Furthermore, there should only be one grounding system in
    a home.  Some codes require more than one grounding electrode.
    These will be connected together, or connected to the neutral
    at a common point - still one grounding system.  Adding additional
    grounding electrodes connected to other portions of the house
    wiring is unsafe and contrary to code.

    If you add a subpanel, the ground and neutral are usually
    brought as separate conductors from the main panel, and are
    not connected together in the subpanel (ie: still only one
    neutral-ground connection).  However, in some situations
    (certain categories of separate buildings) you actually do
    have to provide a second grounding electrode - consult your
    inspector.

    The other two wires will usually be black, and are the "hot"
    wires.  They are attached to the distribution transformer as
    well.

    The two black wires are 180 degrees out of phase with each
    other.  This means if you connect something to both hot wires,
    the voltage will be 220 volts.  If you connect something to the
    white and either of the two blacks you will get 110V.

    Some panels seem to only have three wires coming into them.
    This is either because the neutral and ground are connected
    together at a different point (eg: the meter or pole) and one
    wire is doing dual-duty as both neutral and ground, or in some
    rare occasions, the service has only one hot wire (110V only
    service).

------------------------------
Subject: What is a circuit?

    Inside the panel, connections are made to the incoming wires.
    These connections are then used to supply power to selected
    portions of the home.  There are three different combinations:
        1) one hot, one neutral, and ground: 110V circuit.
        2) two hots, no neutral, and ground: 220V circuit.
        3) two hots, neutral, and ground: 220V circuit + neutral,
           and/or two 110V circuits with a common neutral.

    (1) is used for most circuits supplying receptacles and
    lighting within your house.  (3) is usually used for supplying
    power to major appliances such as stoves, and dryers - they
    often have need for both 220V and 110V, or for bringing several
    circuits from the panel box to a distribution point.  (2) is
    usually for special 220V motor circuits, electric heaters, or
    air conditioners.

    [Note: In the US, the NEC frequently permits a circuit similar
    to (2) be used for stoves and dryers - namely, that there
    are two hot wires, and a wire that does dual duty as neutral
    and ground, and is connected to the frame as well as providing
    the neutral for 110V purposes - three prong plugs instead
    of four (*only* for stoves/dryers connected to the main panel.
    When connected to most sub-panels, 4 prong plugs and receptacles
    are required).  In our not-so-humble opinion this is crazy, but
    the NFPA claims that this practice was re-evaluated for the 1992 NEC,
    and found to be safe.  Check your local codes, or inquire as to
    local practice -- there are restrictions on when this is
    permissible.]

    (1) is usually wired with three conductor wire: black for hot,
    white for neutral, and bare for grounding.

    (2) and (3) have one hot wire coloured red, the other black, a
    bare wire for grounding, and in (3) a white wire for neutral.

    You will sometimes see (2) wired with just a black, white and ground
    wire.  Since the white is "hot" in this case, both the NEC and CEC
    requires that the white wire be "permanently marked" at the ends
    to indicate that it is a live wire.  Usually done with paint, nail
    polish or sometimes electrical tape.

    Each circuit is attached to the main wires coming into the
    panel through a circuit breaker or fuse.

    There are, in a few locales, circuits that look like (1), (2)
    or (3) except that they have two bare ground wires.  Some places
    require this for hot tubs and the like (one ground is "frame ground",
    the other attaches to the motor).  This may or may not be an
    alternative to GFCI protection.

------------------------------
Subject: "grounding" versus "grounded" versus "neutral".

    According to the terminology in the CEC and NEC, the
    "grounding" conductor is for the safety ground, i.e., the green
    or bare or green with a yellow stripe wire.  The word "neutral"
    is reserved for the white when you have a circuit with more than
    one "hot" wire.  Since the white wire is connected to neutral and
    the grounding conductor inside the panel, the proper term is
    "grounded conductor".  However, the potential confusion between
    "grounded conductor" and "grounding conductor" can lead to
    potentially lethal mistakes - you should never use the bare wire
    as a "grounded conductor" or white wire as the "grounding conductor",
    even though they are connected together in the panel.

    [But not in subpanels - subpanels are fed neutral and ground
    separately from the main panel.  Usually.]

    Note: do not tape, colour or substitute other colour wires for the
    safety grounding conductor.

    In the trade, and in common usage, the word "neutral" is used
    for "grounded conductor".  This FAQ uses "neutral" simply to
    avoid potential confusion.  We recommend that you use "neutral"
    too.  Thus the white wire is always (except in some light
    switch applications) neutral.  Not ground.

------------------------------
Subject: What does a fuse or breaker do?  What are the differences?

    Fuses and circuit breakers are designed to interrupt the power
    to a circuit when the current flow exceeds safe levels.  For
    example, if your toaster shorts out, a fuse or breaker should
    "trip", protecting the wiring in the walls from melting.  As
    such, fuses and breakers are primarily intended to protect the
    wiring -- UL or CSA approval supposedly indicates that the
    equipment itself won't cause a fire.

    Fuses contain a narrow strip of metal which is designed to melt
    (safely) when the current exceeds the rated value, thereby
    interrupting the power to the circuit.  Fuses trip relatively
    fast.  Which can sometimes be a problem with motors which have
    large startup current surges.  For motor circuits, you can use
    a "time-delay" fuse (one brand is "fusetron") which will avoid
    tripping on momentary overloads.  A fusetron looks like a
    spring-loaded fuse.  A fuse can only trip once, then it must be
    replaced.

    Breakers are fairly complicated mechanical devices.  They
    usually consist of one spring loaded contact which is latched
    into position against another contact.  When the current flow
    through the device exceeds the rated value, a bimetallic strip
    heats up and bends.  By bending it "trips" the latch, and the
    spring pulls the contacts apart.  Circuit breakers behave
    similarly to fusetrons - that is, they tend to take longer to
    trip at moderate overloads than ordinary fuses.  With high
    overloads, they trip quickly.  Breakers can be reset a finite
    number of times - each time they trip, or are thrown
    when the circuit is in use, some arcing takes place, which
    damages the contacts.  Thus, breakers should not be used in
    place of switches unless they are specially listed for the
    purpose.

    Neither fuses nor breakers "limit" the current per se.  A dead
    short on a circuit can cause hundreds or sometimes even
    thousands of amperes to flow for a short period of time, which
    can often cause severe damage.

------------------------------
Subject: Breakers?  Can't I use fuses?

    Statistics show that fuse panels have a significantly higher
    risk of causing a fire than breaker panels.  This is usually
    due to the fuse being loosely screwed in, or the contacts
    corroding and heating up over time, or the wrong size fuse
    being installed, or the proverbial "replace the fuse with a
    penny" trick.

    Since breakers are more permanently installed, and have better
    connection mechanisms, the risk of fire is considerably less.

    Fuses are prone to explode under extremely high overload.  When
    a fuse explodes, the metallic vapor cloud becomes a conducting
    path.  Result?  From complete meltdown of the electrical panel,
    melted service wiring, through fires in the electrical
    distribution transformer and having your house burn down.
    [This author has seen it happen.]  Breakers won't do this.

    Many jurisdictions, particularly in Canada, no longer permit
    fuse panels in new installations.  The NEC does permit new
    fuse panels in some rare circumstances (requiring the special
    inserts to "key" the fuseholder to specific size fuses)

    Some devices, notably certain large air conditioners, require fuse
    protection in addition to the breaker at the panel.  The fuse
    is there to protect the motor windings from overload.  Check the
    labeling on the unit.  This is usually only on large permanently
    installed motors.  The installation instructions will tell you
    if you need one.

------------------------------
Subject: What size wire should I use?

    For a 20 amp circuit, use 12 gauge wire.  For a 15 amp circuit,
    you can use 14 gauge wire (in most locales).  For a long run,
    though, you should use the next larger size wire, to avoid
    voltage drops.  12 gauge is only slightly more expensive than
    14 gauge, though it's stiffer and harder to work with.

    Here's a quick table for normal situations.  Go up a size for
    more than 100 foot runs, when the cable is in conduit, or
    ganged with other wires in a place where they can't dissipate
    heat easily:

        Gauge        Amps
        14        15
        12        20
        10        30
        8        40
        6        65

    We don't list bigger sizes because it starts getting very dependent
    on the application and precise wire type.

------------------------------
Subject: Where do these numbers come from?

    There are two considerations, voltage drop and heat buildup.
    The smaller the wire is, the higher the resistance is.  When
    the resistance is higher, the wire heats up more, and there is
    more voltage drop in the wiring.  The former is why you need
    higher-temperature insulation and/or bigger wires for use in
    conduit; the latter is why you should use larger wire for long
    runs.

    Neither effect is very significant over very short distances.
    There are some very specific exceptions, where use of smaller
    wire is allowed.  The obvious one is the line cord on most
    lamps.  Don't try this unless you're certain that your use fits
    one of those exceptions; you can never go wrong by using larger
    wire.

------------------------------
Subject: What does "14-2" mean?

    This is used to describe the size and quantity of conductors
    in a cable.  The first number specifies the gauge.  The second
    the number of current carrying conductors in the wire - but
    remember there's usually an extra ground wire.  "14-2" means
    14 gauge, two insulated current carrying wires, plus bare ground.

    -2 wire usually has a black, white and bare ground wire.  Sometimes
    the white is red instead for 220V circuits without neutral.  In
    the latter case, the sheath is usually red too.

    -3 wire usually has a black, red, white and bare ground wire.
    Usually carrying 220V with neutral.

------------------------------
Subject: What is a "wirenut"/"marrette"/"marr connector"?  How are they
    used?

    A wire nut is a cone shaped threaded plastic thingummy that's used
    to connect wires together.  "Marrette" or "Marr connector"
    are trade names.  You'll usually use a lot of them in DIY wiring.

    In essence, you strip the end of the wires about an inch, twist them
    together, then twist the wirenut on.

    Though some wirenuts advertise that you don't need to twist the
    wire, do it anyways - it's more mechanically and electrically
    secure.

    There are many different sizes of wire nut.  You should check
    that the wire nut you're using is the correct size for the
    quantity and sizes of wire you're connecting together.

    Don't just gimble the wires together with a pair of pliers or
    your fingers.  Use a pair of blunt nose ("linesman") pliers,
    and carefully twist the wires tightly and neatly.  Sometimes
    it's a good idea to trim the resulting end to make sure it
    goes in the wirenut properly.

    Some people wrap the "open" end of the wirenut with electrical
    tape.  This is probably not a good idea - the inspector may
    tear it off during an inspection.  It's usually done because
    a bit of bare wire is exposed outside the wire nut - instead
    of taping it, the connection should be redone.

------------------------------
Subject: What is a GFI/GFCI?

    A GFCI is a ``ground-fault circuit interrupter''.  It measures
    the current current flowing through the hot wire and the
    neutral wire.  If they differ by more than a few milliamps, the
    presumption is that current is leaking to ground via some other
    path.  This may be because of a short circuit to the chassis of
    an appliance, or to the ground lead, or through a person.  Any
    of these situations is hazardous, so the GFCI trips, breaking
    the circuit.

    GFCIs do not protect against all kinds of electric shocks.  If,
    for example, you simultaneously touched the hot and neutral
    leads of a circuit, and no part of you was grounded, a GFCI
    wouldn't help.  All of the current that passed from the hot
    lead into you would return via the neutral lead, keeping the
    GFCI happy.

    The two pairs of connections on a GFCI outlet are not symmetric.
    One is labeled LOAD; the other, LINE.  The incoming power feed
    *must* be connected to the LINE side, or the outlet will not be
    protected.  The LOAD side can be used to protect all devices
    downstream from it.  Thus, a whole string of outlets can be
    covered by a single GFCI outlet.

------------------------------
Subject: Where should GFCIs be used?

    The NEC mandates GFCIs for 110V, 15A or 20A single phase
    outlets, in bathrooms, kitchens within 6' of the sink, wet-bar
    sinks, roof outlets, garages, unfinished basements or crawl spaces,
    outdoors, near a pool, or just about anywhere else where you're likely
    to encounter water or dampness.  There are exceptions for inaccessible
    outlets, those dedicated to appliances ``occupying fixed space'',
    typically refrigerators and freezers, and for sump pumps and
    laundry appliances.

    The NEC now requires that if your replace an outlet in a
    location now requiring GFCI, you must install GFCI protection.
    Note in particular - kitchen and bathroom outlets.

    When using the "fixed appliance" rule for avoiding GFCI outlets,
    single outlet receptacles must be used for single appliances,
    duplex receptacles may be used for two appliances.

    The CEC does not mandate as many GFCIs.  In particular, there
    is no requirement to protect kitchen outlets, or most garage or
    basement outlets.  Basement outlets must be protected if you
    have a dirt floor, garage outlets if they're near the door to
    outside.  Bathrooms and most exterior outlets must have GFCIs,
    as do pools systems and jacuzzi or whirlpool pumps.

    There are many rules about GFCIs with pools and so on.  This
    is outside of our expertise, so we're not covering it in
    detail.  See your inspector.

    When replacing an outlet, it must now be GFCI-protected if
    such would now be required for a new installation.  That is,
    a kitchen outlet installed per the 1984 code need not have
    been protected, but if that outlet is ever replaced, GFCI
    protection must now be added (under NEC).  This is explicit
    in the 1993 NEC, and inspector-imposed in Canada.

    Even if you are not required to have GFCI protection, you may
    want to consider installing it anyway.  Unless you need a GFCI
    breaker (see below), the cost is low.  In the U.S., GFCI
    outlets can cost as little as US$8.  (Costs are a bit higher in
    Canada:  C$12.)  Evaluate your own risk factors.  Does your
    finished basement ever get wet?  Do you have small children?
    Do you use your garage outlets to power outdoor tools?  Does
    water or melted snow ever puddle inside your garage?

------------------------------
Subject: Where shouldn't I use a GFCI?

    GFCIs are generally not used on circuits that (a) don't pose a
    safety risk, and (b) are used to power equipment that must run
    unattended for long periods of time.  Refrigerators, freezers,
    and sump pumps are good examples.  The rationale is that GFCIs
    are sometimes prone to nuisance trips.  Some people claim that
    the inductive delay in motor windings can cause a momentary
    current imbalance, tripping the GFCI.  Note, though, that most
    GFCI trips are real; if you're getting a lot of trips for no
    apparent reason, you'd be well-advised to check your wiring
    before deciding that the GFCI is broken or useless.

------------------------------
Subject: What is the difference between a GFCI outlet and a GFCI breaker?

    For most situations, you can use either a GFCI outlet as the
    first device on the circuit, or you can install a breaker with
    a built-in GFCI.  The former is generally preferred, since GFCI
    breakers are quite expensive.  For example, an ordinary GE
    breaker costs ~US$5; the GFCI model costs ~US$35.  There is one
    major exception:  if you need to protect a ``multi-wire branch
    circuit'' (two or more circuits sharing a common neutral wire),
    such as a Canadian-style kitchen circuit, you'll need a
    multi-pole GFCI breaker.  Unfortunately, these are expensive;
    the cost can range into the hundreds of dollars, depending on
    what brand of panel box you have.  But if you must protect such
    a circuit (say, for a pool heater), you have no choice.

    One more caveat -- GFCI outlets are bulky.  You may want to use
    an oversize box when installing them.  On second thought, use
    large (actually deep) boxes everywhere.  You'll thank yourself
    for it.

    Incidentally, if you're installing a GFCI to ensure that one
    specific outlet is protected (such as a bathroom), you don't
    really have to go to all of the trouble to find the first
    outlet in the circuit, you could simply find the first outlet
    in the bathroom, and not GFCI anything upstream of it.  But
    protecting the whole circuit is preferred.

    When you install a GFCI, it's a good idea to use the little
    "ground fault protected" stickers that come with it and mark
    the outlets downstream of the GFCI.  You can figure out which
    outlets are "downstream", simply by tripping the GFCI with the
    test button and see which outlets are dead.

    Note that the labels are mandatory for GFCI-protected-but-ungrounded
    three prong outlets according to the NEC.

------------------------------
Subject: What's the purpose of the ground prong on an outlet, then?

    Apart from their use in electronics, which we won't comment on,
    and for certain fluorescent lights (they won't turn on without
    a good ground connection), they're intended to guard against
    insulation failures within the device.  Generally, the case of
    the appliance is connected to the ground lead.  If there's an
    insulation failure that shorts the hot lead to the case, the
    ground lead conducts the electricity away safely (and possibly
    trips the circuit breaker in the process).  If the case is not
    grounded and such a short occurs, the case is live -- and if
    you touch it while you're grounded, you'll get zapped.  Of
    course, if the circuit is GFCI-protected, it will be a very
    tiny zap -- which is why you can use GFCIs to replace
    ungrounded outlets (both NEC and CEC).

    There are some appliances that should *never* be grounded.  In
    particular, that applies to toasters and anything else with
    exposed conductors.  Consider:  if you touch the heating
    electrode in a toaster, and you're not grounded, nothing will
    happen.  If you're slightly grounded, you'll get a small shock;
    the resistance will be too high.  But if the case were
    grounded, and you were holding it, you'd be the perfect path to
    ground...

------------------------------
Subject: Why is one prong wider than the other?  Polarization

    Nowadays, many two-prong devices have one prong wider than the
    other.  This is so that the device could rely (not guaranteed!)
    on one specific wire being neutral, and the other hot.
    This is particularly advantageous in light fixtures, where the
    the shell should neutral (safety), or other devices which want to
    have an approximate ground reference (ie: some radios).

    Most 2-prong extension cords have wide prongs too.

    This requires that you wire your outlets and plugs the right
    way around.  You want the wide prong to be neutral, and the
    narrow one hot.  Most outlets have a darker metal for the
    hot screw, and lighter coloured screw for the neutral.
    If not, you can usually figure out which is which by which
    prong the terminating screw connects to.

------------------------------
Subject: How do I convert two prong receptacles to three prong?

    Older homes frequently have two-prong receptacles instead
    of the more modern three.  These receptacles have no safety
    ground, and the cabling usually has no ground wire.  Neither
    the NEC or CEC permits installing new 2 prong receptacles anymore.

    There are several different approaches to solving this:
        1) If the wiring is done through conduit or BX, and the
           conduit is continuous back to the panel, you can connect
           the third prong of a new receptacle to the receptacle
           box.  NEC mainly - CEC frowns on this practice.
        2) If there is a copper cold water pipe going nearby, and
           it's continuous to the main house ground point, you can
           run a conductor to it from the third prong.
           NEC: this can only be done if the point of attachment
           is within 5 feet of where the pipe enters the ground.
        3) Run a ground conductor back to the main panel.
        4) Easiest: install a GFCI receptacle.  The ground lug
           should not be connected to anything, but the GFCI
           protection itself will serve instead.  The GFCI
           will also protect downstream (possibly also two prong
           outlets).  If you do this to protect downstream outlets,
           the grounds must not be connected together.  Since it
           wouldn't be connected to a real ground, a wiring fault
           could energize the cases of 3 prong devices connected
           to other outlets.  Be sure, though, that there aren't
           indirect ground plug connections, such as via the sheath
           on BX cable.

    The CEC permits you to replace a two prong receptacle with a three
    prong if you fill the U ground with a non-conducting goop.
    Like caulking compound.  This is not permitted in the NEC.

    The NEC requires that three prong receptacles without ground
    that are protected by GFCI must be labelled as such.

    See the next section about computers on GFCI-protected groundless
    outlets.

------------------------------
Subject: Surges, spikes, zaps, grounding and your electronics

    Theoretically, the power coming into your house is a perfect AC
    sine wave.  It is usually quite close.  But occasionally, it
    won't be.  Lightning strikes and other events will affect the
    power.  These usually fall into two general categories: very
    high voltage spikes (often into 1000s of volts, but usually
    only a few microseconds in length) or surges (longer duration,
    but usually much lower voltage).

    Most of your electrical equipment, motors, transformer-operated
    electronics, lights, etc., won't even notice these one-shot
    events.  However, certain types of solid-state electronics,
    particularly computers with switching power supplies and MOS
    semiconductors, can be damaged by these occurances.  For
    example, a spike can "punch a hole" through an insulating layer
    in a MOS device (such as that several hundred dollar 386 CPU),
    thereby destroying it.

    The traditional approach to protecting your electronics is to
    use "surge suppressors" or "line filters".  These are usually
    devices that you plug in between the outlet and your
    electronics.

    Roughly speaking, surge suppressors work by detecting
    overvoltages, and shorting them out.  Think of them as voltage
    limiters.  Line filters usually use frequency-dependent
    circuits (inductors, capacitors etc.) to "tune out" undesirable
    spikes - preventing them from reaching your electronics.

    So, you should consider using suppressors or filters on your
    sensitive equipment.

    These devices come in a very wide price range.  From a couple
    of dollars to several hundred.  We believe that you can protect
    your equipment from the vast majority of power problems by
    selecting devices in the $20-50 range.

    A word about grounding: most suppressors and EFI filters
    require real grounds.  Any that don't are next to useless.

    For example, most surge suppressors use MOVs (metal oxide
    varistors) to "clamp" overvoltages.  Yes, you can have a
    suppressor that only has a MOV between neutral and hot to
    combat differential-mode voltage excursions, but that isn't
    enough.  You need common-mode protection too.  Good suppressors
    should have 3 MOVs, one between each pair of wires.  Which
    means you should have a good solid ground.  Eg: a solidly
    connected 14ga wire back to the panel.  Not rusty BX armour or
    galvanized pipe with condensation turning the copper connection
    green.

    Without a ground, a surge or spike is free to "lift" your
    entire electronics system well away from ground.  Which is
    ideal for blowing out interface electronics for printer ports
    etc.

    Secondly, static electricity is one of the major enemies of
    electronics.  Having good frame grounds is one way of
    protecting against static zaps.

    If you're in the situation of wanting to install computer
    equipment on two wire groundless circuits take note:

    Adding a GFCI outlet to the circuit makes the circuit safe for
    you.  But it doesn't make it safe for your equipment - you need
    a ground to make surge suppressors or line filters effective.

------------------------------
Subject: Are you sure about GFCIs and ungrounded outlets?
    Should the test button work?

    The NEC, section 210-7(d), and CEC, section 26-700(9), are quite
    explicit that GFCIs are a legal substitute for a grounded outlet
    in an existing installation where there is no ground available in
    the outlet box.

    But your local codes may vary.  As for the TEST button -- there's
    a resistor connecting the LOAD side of the hot wire to the LINE
    side of the neutral wire when you press the TEST button.  Current
    through this resistor shows up as an imbalance, and trips the GFCI.
    This is a simple, passive, and reliable test, and doesn't require
    a real ground to work.  If your GFCI does not trip when you press
    the TEST button, it is very probably defective or miswired.  Again:
    if the test button doesn't work, something's broken, and potentially
    dangerous.  The problem should be corrected immediately.

    The instructions that come with some GFCIs specify that the ground
    wire must be connected.  We do not know why they say this.  The
    causes may be as mundane as an old instruction sheet, or with the
    formalities of UL or CSA listing -- perhaps the device was never
    tested without the ground wire being connected.  On the other hand,
    UL or CSA approval should only have been granted if the device
    behaves properly in *all* listed applications, including ungrounded
    outlet replacement.  (One of us called Leviton; their GFCIs are
    labeled for installation on grounded circuits only.  The technician
    was surprised to see that; he agreed that the NEC does not require
    it, and promised to investigate.)

--
Chris Lewis: _Una confibula non sat est_
Phone: Canada 613 832-0541
Latest psroff: FTP://ftp.uunet.ca/distrib/chris_lewis/psroff3.0pl17/*
Latest hp2pbm: FTP://ftp.uunet.ca/distrib/chris_lewis/hp2pbm/*
Archive-name: electrical-wiring/part2
Last-modified: Mon Nov 14 01:03:29 EST 1994

            Copyright 1991, 1992, 1993
              Chris Lewis and Steven Bellovin

        Redistribution for profit, or in altered content/format
        prohibited without permission of the authors.  Other
        redistribution must contain this copyright notice,
        and attribution.

The latest FAQ can always be obtained from:

    ftp://rtfm.mit.edu/pub/usenet/news.answers/electrical-wiring/part[1-2]

------------------------------
Subject: What kind of outlets do I need in a kitchen?

    The NEC requires at least two 20 amp ``small appliance
    circuits'' for kitchen counters.  The CEC requires split-duplex
    receptacles.  Outlets must be installed such that no point is more
    than 24" (NEC) (900 mm CEC) from an outlet.  Every counter wider
    than 12" (NEC) or 300 mm (CEC) must have at least one outlet.
    The circuit these outlets are on may not feed any outlets except
    in the kitchen, pantry, or dining room.  Furthermore, these circuits
    are in addition to any required for refrigerators, stoves, microwaves,
    lighting, etc.  Non-dedicated outlets within 6' of a sink *must* be
    protected by a GFCI (NEC only).

    Split duplex receptacles are fed with a 220V circuit.  The tab
    is broken on the hot side of the outlet, and one hot goes to
    the upper outlet, and the other hot goes to the lower outlet.
    The neutral connects to both outlets through one screw.  When
    "carrying through" to another outlet, the neutral must be
    pigtailed, such that removing the outlet, or having the neutral
    connection fall off or burn out doesn't cause the neutral to
    disconnect from downstream outlets ("loose neutral" problems -
    see "What does it mean when the lights brighten...").

------------------------------
Subject: Where must outlets and switches be in bathrooms?

    There must be at least one outlet in each bathroom, adjacent to
    the sink, in addition to any outlet that may be incorporated in
    the light fixture.  All such outlets *must* be GFCI-protected.

    The NEC says that switches may not be installed inside bathtubs
    or showers.  The CEC says that switches may not be installed
    "within reach" of bathtubs or showers (consult an inspector
    if you can't make it at least four feet).

------------------------------
Subject: General outlet placement rules/line capacities

    We paraphrase CEC 26-702 (NEC: 210-52 through 210-63)

    Note: In laying out receptacle outlets, consideration shall be
    given to the placement of electrical baseboards, hot air
    registers, hot water or steam registers, with a view of
    eliminating cords having to pass over hot or conductive
    surfaces wherever possible.

    NEC:  You're not allowed to put outlets over electric
    baseboards.  That, coupled with the spacing requirements, more
    or less mandates the use of baseboards with integral outlets.
    Note that such outlets are fed by a different branch circuit
    than the heating elements.

    2. Except as otherwise required, receptacles shall be installed
    in the finished walls of every room or area, other than
    kitchens, bathrooms, hallways, laundry rooms, utility rooms or
    closets, so that no point along the floor line of any usable
    wall space is more than 1.8m (6') horizontally from a
    receptacle in that or an adjoining space, such distance being
    measured along the floor line of the wall spaces involved.

    Fixed dividers, counters, etc., are considered wall space.
    Floor outlets do not satisfy the requirement unless they are
    ``near'' the wall.  Insofar as practical, outlets should be
    spaced equidistantly.

    3. At least one duplex receptacle shall be provided in each
    enclosed area such as a balcony or porch that is not classified
    as a finished room or area.

    [NEC doesn't seem to have this rule.]

    4. The receptacles referred to in (2) and (3) shall be duplex
    receptacles or equivalent number of single receptacles.

    5. "Usable wall space" is defined as any wall space 900mm (3',
    NEC 2') or more in width, not to include doorways, areas
    occupied by a door when fully opened, windows which extend to
    the floor, fireplaces or other permanent installations that
    would limit the use of the wall space.

    6.  See kitchen counter requirements.  At least one duplex
    receptacle in eat-in dining area.

    [We don't think the latter part is in the NEC.  Also, the NEC
    says that the two 20-amp small appliance circuits can't go
    outside of the kitchen, dining room, pantry, etc., nor can they
    be used for anything else, except for things like clock
    outlets, stove accessory outlets, etc.]

    7. Receptacles shall not be mounted facing up in the work
    surfaces or counters of the kitchen or dining area.

    8. No point in a hallway within a dwelling unit shall be more
    than 4.5m (15', NEC 10') from a duplex receptacle as measured
    by the shortest path which the supply cord of an appliance
    connected to the receptacle would follow without passing
    through an openning fitted with a door.  (vacuum-cleaner
    rule).

    9. At least one duplex receptacle shall be provided: in laundry
    room, utility room and any unfinshed basement area

    [NEC: see GFCI requirements.  There must be a dedicated 20 amp
    laundry receptacle, with no other outlets, plus an additional
    unfinished basement receptacle.  Any attic or crawl space with
    heating or air conditioning equipment must have a receptacle.
    (this is probably in the CEC too.)]

    10, 11, 12, 13:  See bathroom requirements, GFCI, washing
    machine outlet placement.

    14, 15. Outlets shall not be placed in ironing cabinets,
    cupboards, wall cabinets, nor in similar enclosures except
    where they're for specific non-heating appliances (including
    microwave) in the enclosure.

    [NEC: No such requirement.  Are you sure Steven?]

    16, 17. For each single-family dwelling, at least one duplex
    receptacle shall be installed outdoors to be readily available
    from ground level (see GFCI requirements).  Appendix B
    (additional notes) suggests front and back outlets to be
    controlled by an interior switch.

    [NEC:  One in front, one in back.  No discussion of them being
    switched.]

    18. At least one duplex receptacle shall be provided for each
    car space in a garage or carport.

    [NEC:  For an attached garage, or detached garage with electric
    service -- but there is no requirement that detached garages
    have power.  This remark is probably relevant to CEC as well.]

    19. For the purposes of this rule, all receptacles shall be of
    the grounding type, configuration 5-15R (standard 110V/15A 3
    prong).

    20. Any receptacle that is part of a lighting fixture or
    appliance that is > 1.7m (5 feet) above the floor, or in
    cabinets or cupboards, is not counted in the above rules.

    21. Where a switched duplex outlet is used in lieu of a light
    outlet and fixture, the receptacle shall be considered one of
    the wall mounted receptacles required here.

    22. At least one duplex receptacle shall be provided for a
    central vacuum system if the ducting is installed.

    [NEC:  couldn't find an equivalent rule.]

    Capacities: Knight recommends no more than 10 outlets per
    circuit.  Some US references talk about a limit of 12.  There
    appears to be a wattage/area/outlet count calculation somewhere
    in the NEC.  20A circuits may have different rules.

    It is open to considerable debate whether you should mix
    general lighting and outlets on individual circuits.  Knight
    recommends it.  Some netters don't.  I tend towards the former
    for load balancing reasons.

    NEC: There's a new rule on outdoor outlets.  If exposed to the
    weather, and if used for unattended equipment (pool filters,
    outdoor lighting, etc.), the outlet must still be weatherproof
    even when the device is plugged in.

------------------------------
Subject: What is Romex/NM/NMD?  What is BX?  When should I use each?

    Romex is a brand name for a type of plastic insulated wire.
    Sometimes called non-metallic sheath.  The formal name is NM.
    This is suitable for use in dry, protected areas (ie: inside
    stud walls, on the sides of joists etc.), that are not subject
    to mechanical damage or excessive heat.  Most newer homes are
    wired almost exclusively with NM wire.  There are several
    different categories of NM cable.

    BX cable -- technically known as armored cable or "AC" has a
    flexible aluminum or steel sheath over the conductors and is
    fairly resistant to damage.

    TECK cable is AC with an additional external thermoplastic
    sheath.

    Protection for cable in concealed locations: where NM or AC cable
    is run through studs, joists or similar wooden members, the outer
    surface of the cable must be kept at least 32mm/1.25" (CEC & NEC)
    from the edges of the wooden members, or the cable should be protected
    from mechanical injury.  This latter protection can take the form of
    metal plates (such as spare outlet box ends) or conduit.

    [Note: inspector-permitted practice in Canada suggests that armored
    cable, or flexible conduit can be used as the mechanical protection,
    but this is technically illegal.]

    Additional protection recommendations: [These are rules in the
    Canadian codes.  The 1993 NEC has many changes that bring
    it close to these rules.  These are reasonable answers to the
    vague "exposed to mechanical damage" in both the NEC and CEC.]

        - NM cable should be protected against mechanical damage
          where it passes through floors or on the surface of walls
          in exposed locations under 5 feet from the floor.
          Ie: use AC instead, flexible conduit, wooden guards etc.
        - Where cable is suspended, as in, connections to furnaces
          or water heaters, the wire should be protected.  Canadian
          practice is usually to install a junction or outlet
          box on the wall, and use a short length of AC cable
          or NM cable in flexible conduit to "jump" to the appliance.
          Stapling NM to a piece of lumber is also sometimes used.
        - Where NM cable is run in close proximity to heating
          ducts or pipe, heat transfer should be minimized by
          means of a 25mm/1" air space, or suitable insulation
          material (a wad of fiberglass).
        - NM cable shall be supported within 300mm/1' of every box
          or fitting, and at intervals of no more than 1.5m/5'.
          Holes in joists or studs are considered "supports".
          Some slack in the cable should be provided adjacent to
          each box.  [while fishing cable is technically in violation,
          it is permitted where "proper" support is impractical]
        - 2 conductor NM cable should never be stapled on edge.
          [Knight also insists on only one cable per staple, referring
          to the "workmanship" clause, but this seems more honoured
          in the breach...]
        - cable should never be buried in plaster, cement or
          similar finish, except were required by code [Ie: cable
          burial with shallow bedrock.].
        - cable should be protected where it runs behind baseboards.
        - Cable may not be run on the upper edge of ceiling joists
          or the lower edges of rafters where the headroom is more
          than 1m (39").

    Whenever BX cable is terminated at a box with a clamp, small
    plastic bushings must be inserted in the end of the cable to
    prevent the clamps forcing the sharp ends of the armor through
    the insulation.

    Whenever BX cable is buried in thermal insulation, 90C
    wire should be selected, but derated in current carrying
    capacity to 60C.

    BX is sometimes a good idea in a work shop unless covered by
    solid wall coverings.

    In places where damage is more likely (like on the back wall of
    a garage ;-), you may be required to use conduit, a
    UL- (or CSA-) approved metal pipe.  You use various types of
    fittings to join the pipe or provide entrance/exit for the
    wire.

    Service entrances frequently use a plastic conduit.

    In damp places (eg: buried wiring to outdoor lighting) you will
    need special wire (eg: CEC NMW90, NEC UF).  NMW90 looks like
    very heavy-duty NMD90.  You will usually need short lengths of
    conduit where the wire enters/exits the ground.  [See underground
    wiring section.]

     Thermoplastic sheath wire (such as NM, NMW etc.) should not be
     exposed to direct sunlight unless explicitly approved for that
     purpose.

    Many electrical codes do not permit the routing of wire through
    furnace ducts, including cold air return plenums constructed
    by metal sheeting enclosing joist spaces.   The reason for this
    is that if there's a fire, the ducting will spread toxic gasses
    from burning insulation very rapidly through the building.
    Teflon insulated wire is permitted in plenums in many areas.

     Canada appears to use similar wire designations to the US,
     except that Canadian wire designations usually include the
     temperature rating in Celsius.  Eg: "AC90" versus "AC".
    In the US, NM-B is 90 degrees celcius.

    NOTE: local codes vary.  This is one of the items that changes
    most often.  Eg: Chicago codes require conduit *everywhere*.
    There are very different requirements for mobile homes.
    Check your local codes, *especially* if you're doing anything
    that's the slightest out of the ordinary.

    Wire selection table (incomplete - the real tables are enormous,
    uncommon wire types or applications omitted)

    Condition            Type    CEC    NEC

    Exposed/Concealed dry        plastic    NMD90    NM
                    armor    AC90    AC
                        TECK90

    Exposed/Concealed damp        plastic    NMD90    NMC
                    armor    ACWU90
                        TECK90

    Exposed/Concealed wet        plastic    NMWU90
                    armor    ACWU90
                        TECK90

    Exposed to weather        plastic    NMWU
                        TW etc.
                    armor    TECK90

    Direct earth burial/        plastic    NMWU*    UF
    Service entrance            RWU
                        TWU
                    armor    RA90
                        TECK90
                        ACWU90
    [* NMWU not for service entrance]

------------------------------
Subject: Should I use plastic or metal boxes?

    The NEC permits use of plastic boxes with non-metallic cable
    only.  The reasoning is simple -- with armored cable, the box
    itself provides ground conductor continuity.  U.S. plastic
    boxes don't use metal cable clamps.

    The CEC is slightly different.  The CEC never permits cable
    armor as a grounding conductor.  However, you must still
    provide ground continuity for metallic sheath.  The CEC also
    requires grounding of any metal cable clamps on plastic boxes.

    The advantage of plastic boxes is comparatively minor even for
    non-metallic sheathed cable -- you can avoid making one ground
    connection and they sometimes cost a little less.  On the other
    hand, plastic boxes are more vulnerable to impacts.  For
    exposed or shop wiring, metal boxes are probably better.

    Metal receptacle covers must be grounded, even on plastic
    boxes.  This may be achieved by use of a switch with ground
    connection.

------------------------------
Subject: Junction box positioning?

    A junction box is a box used only for connecting wires together.

    Junction boxes must be located in such a way that they're accessible
    later.  Ie: not buried under plaster.  Excessive use of junction
    boxes is often a sign of sloppy installation, and inspectors may
    get nasty.

------------------------------
Subject: Can I install a replacement light fixture?

    In general, one can replace fixtures freely, subject to a few
    caveats.  First, of course, one should check the amperage
    rating of the circuit.  If your heart is set on installing half
    a dozen 500 watt floodlights, you may need to run a new wire
    back to the panel box.  But there are some more subtle
    constraints as well.  For example, older house wiring doesn't
    have high-temperature insulation.  The excess heat generated by
    a ceiling-mounted lamp can and will cause the insulation to
    deteriorate and crack, with obvious bad results.  Some newer
    fixtures are specifically marked for high temperature wire
    only.  (You may find, in fact, that your ceiling wiring already
    has this problem, in which case replacing any devices is a real
    adventure.)

    Other concerns include providing a suitable ground for some
    fluorescent fixtures, and making sure that the ceiling box and
    its mounting are strong enough to support the weight of a heavy
    chandelier or ceiling fan.  You may need to install a new box
    specifically listed for this purpose.  A 2x4 across the ceiling
    joists makes a good support.  Metal brackets are also available
    that can be fished into ceilings thru the junction box hole and
    mounted between the joists.

    There are special rules for recessed light fixtures such as
    "pot" lamps or heat lamps.  When these are installed in
    insulated ceilings, they can present a very substantial fire
    hazard.  The CEC provides for the installation of pot lamps in
    insulated ceilings, provided that the fixture is boxed in a
    "coffin" (usually 8'x16"x12" - made by making a pair of joists
    12" high, and covering with plywood) that doesn't have any
    insulation.  (Yes, that's 8 *feet* long)

    NEC rules are somewhat less stringent.  They require at least
    3" clearance between the fixture and any sort of thermal
    insulation.  The rules also say that one should not obstruct
    free air movement, which means that a CEC-style ``coffin''
    might be worthwhile.  Presumably, that's up to the local
    inspector.  [The CEC doesn't actually mandate the coffin
    per-se, this seems to be an inspector requirement to make
    absolutely certain that the fixture can't get accidentally
    buried in insulation.  Ie: if you have insulation blown in
    later.]

    There are now fixtures that contain integral thermal cutouts
    and fairly large cases that can be buried directly in
    insulation.  They are usually limited to 75 watt bulbs, and are
    unfortunately, somewhat more expensive than the older types.
    Before you use them, you should ensure that they have explicit
    UL or CSA approval for such uses.  Follow the installation
    instructions carefully; the prescribed location for the sensor
    can vary.

    There does not yet appear to be a heat lamp fixture that is
    approved for use in insulation.  The "coffin" appears the only
    legal approach.

------------------------------
Subject: Noisy fluorescent fixtures, what do I do?

    Many fluorescent fixtures tend to buzz, objectionably so when used in
    residential (rather than warehouse or industrial) situations.  This
    tends to be the result of magnetic/physical resonances at the
    (low) frequencies that standard fixture ballasts operate.  You
    can eliminate this problem by switching to electronic ballasts,
    which operate at a higher (inaudible) frequency.  Unfortunately,
    these are quite expensive.

-----------------------------
Subject: Noisy lights with dimmer switches, what do I do?
|
|    Often, after installing a dimmer switch, or replacing bulbs controlled
|    by a dimmer, you'll start hearing objectionable buzzing or humming
|    from the bulb.  Sometimes it even interferes with televisions or radios.
|
|    A little theory first.  The voltage on the wiring in your house looks
|    like this - a sine wave (forgive the lousy ASCII graphics ;-):
|
|                  ...             ...              ~ +160V
|                 .   .           .   .
|                .     .         .     .
|              ------------------------------------ 0V
|                        .     .         .     .
|                         .   .           .   .
|                          ...             ...      ~ -160V
|
|    Most dimmers work by having a solid-state switch called a triac
|    in series with the light bulb.  Whenever the voltage passes through
|    zero (it does this 120 times per second), the triac turns itself off.
|    The control circuitry in the dimmer provides an adjustable delay
|    before the triac turns back on.  So, the resulting wave form looks
|    like this:
|
|                  ...             ...              ~ +160V
|                  |  .            |  .
|                  |   .           |   .
|              ------------------------------------ 0V
|                          |   .           |   .
|                          |  .            |  .
|                          ...             ...      ~ -160V
|
|
|    As you can see, by varying the turn-on point, the amount of
|    power getting to the bulb is adjustable, and hence the light
|    output can be controlled.  Voila, a dimmer!
|
|    This is where it gets interesting.  Note the sharp corners.
|    According to the Nyquist theorem, those corners effectively
|    consist of 60Hz plus varying amounts of other frequencies that
|    are multiples of 60Hz.  In some cases up to 1Mhz and more.  The
|    wiring in your house acts as an antenna and essentially
|    broadcasts it into the air.  Hence TVs and radios can be
|    effected.  This is called EMI (Electromagnetic Interference).
|
|    As far as the bulbs are concerned, a bulb consists of a series
|    of supports and, essentially, fine coils of wire.   When you
|    run current through a coil, it becomes a magnet right?  If
|    there's any other metal nearby, it'll move.  Just like a
|    solenoid.  Further, when the amount of current flow abruptly
|    changes the magnetism change can be much stronger than it is on
|    a simple sine wave.  Hence, the filaments of the bulb will tend
|    to vibrate more with a dimmer chopping up the wave form, and
|    when the filaments vibrate against their support posts, you
|    will get a buzz.
|
|    Worse, some dimmers only do half-wave switching, such that the
|    one half of the chopped wave form will be absent.  Which means
|    that the current flow during the present half will have to be
|    much stronger to produce the same amount of light - more EMI
|    and more tendency to buzz.
|
|    Solving buzzing problems:  If you have buzzing, it's always
|    worth trying to replace the bulb with a different brand.  Some
|    cheap bulb brands have inadequate filament support, and simply
|    changing to a different brand may help.  Try "rough service" or
|    "farm service" bulbs.  They're usually much stronger and better
|    supported.
|
|    Chance are, however, that switching bulbs won't make that much
|    of a difference.  Perhaps the buzzing will go away at some
|    dimmer settings, but not at all.
|
|    Buzzing bulbs are usually a sign of a "cheap" dimmer.  Dimmers
|    are supposed to have filters in them.  The filter's job is to
|    "round off" the sharp corners in the chopped waveform, thereby
|    reducing EMI, and the abrupt current jumps that can cause
|    buzzing.  In cheap dimmers, they've economized on the
|    manufacturing costs by cost-reducing the filtering, making it
|    less effective.  Perhaps the dimmer will be okay at some
|    settings, but not others.  Or be very picky about what bulbs to
|    use.
|
|    It is our belief that most buzzing problems can be traced down
|    to cheap (<$15 dimmers), and most effectively solved by going
|    to mid-range ($25-$35) dimmers from respected companies, such
|    as Leviton.  One of the authors of this FAQ, after learning
|    this lesson, will still use $.89 outlets, but insists on better
|    dimmers.  By all means, try a different bulb first.  You may
|    get lucky.  If not, it's time to swap dimmers.
|
|    If you have EMI problems, it's almost certain to be a cheap
|    dimmer.

-----------------------------
Subject: What does it mean when the lights brighten when a motor starts?

    This usually means that the neutral wire in the panel is
    loose.  Depending on the load balance, one hot wire may end up
    being more than 110V, and the other less than 110V, with
    respect to ground.  This is a very hazardous situation - it can
    destroy your electronic equipment, possibly start fires, and in
    some situations electrocute you (ie: some US jurisdictions
    require the stove frame connected to neutral).

    If this happens, contact your electrical authority immediately
    and have them come and check out the problem.  If you say "loose
    neutral", they will come.

    Note: a brief (< 1 second) brightening is sometimes normal with
    lighting and motors on the same 220V with neutral circuit.  A
    loose main panel neutral will usually show increased brightness
    far longer than one second.  In case of doubt, get help.

------------------------------
Subject: What is 3 phase power?  Should I use it?  Can I get it in my house?

    Three phase power has three "hot" wires, 120 degrees out of
    phase with each other.  These are usually used for large motors
    because it is more "efficient", provides a bit more starting torque,
    and because the motors are simpler and hence cheaper.

    You're most likely to encounter a 3 phase circuit that shows
    110 volts between any hot and ground, and 208 volts between
    any two hots.  The latter shows the difference between a normal
    220V/110V common neutral circuit, which is 240 volts between the
    two hots.  There are 3 phase circuits with different voltages.

    Bringing in a 3 phase feed to your house is usually
    ridiculously expensive, or impossible.  If the equipment you
    want to run has a standard motor mount, it is *MUCH* cheaper to
    buy a new 110V or 220V motor for it.  In some cases it is
    possible to run 3 phase equipment on ordinary power if you have
    a "capacitor start" unit, or use a larger motor as a
    (auto-)generator.  These are tricky, but are a good solution if
    the motor is non-standard size, or too expensive or too big to
    replace.  The Taunton Press book ``The Small Shop'' has an
    article on how to do this if you must.

    Note that you lose any possible electrical efficiency by using
    such a converter.  The laws of thermodynamics guarantee that.

------------------------------
Subject: Is it better to run motors at 110 or 220?

    Theoretically, it doesn't make any difference.  However, there
    is a difference is the amount of power lost in the supply
    wiring.  All things being equal, a 110V motor will lose 4 times
    more power in the house wiring than a 220V motor.  This also
    means that the startup surge loss will be less, and the motor
    will get to speed quicker with 220V.  And in some circumstances,
    the smaller power loss will lead to longer motor life.

    This is usually irrelevant unless the supply wires are more
    than 50 feet long.

------------------------------
Subject: What is this nonsense about 3HP on 110V 15A circuits?

    It is a universal physical law that 1 HP is equal to 746
    watts.  Given heating loss, power factor and other inefficiencies,
    it is usually best to consider 1 HP is going to need 1000-1200
    watts.  A 110V 15A circuit can only deliver 1850 watts to a motor,
    so it cannot possibly be more than approximately 2 HP.  Given rational
    efficiency factors, 1.5HP is more like it.

    Some equipment manufacturers (Sears in particular, most router
    manufacturers in general ;-) advertise a HP rating that is far
    in excess of what is possible.  They are giving you a "stall
    horsepower" or similar.  That means the power is measured when
    the motor is just about to stop turning because of the load.
    What they don't mention is that if you kept it in that
    condition for more than a few seconds your motor will melt - the
    motor is drawing far more current than its continuous rating.

    When comparing motors, compare the continuous horsepower.  This
    should be on the motor nameplate.  If you can't find that figure,
    check the amperage rating, which is always present.

------------------------------
Subject: How should I wire my shop?

    As with any other kind of wiring, you need enough power for all
    devices that will be on simultaneously.  The code specifies
    that you should stay under 80% of the nominal capacity of the
    circuit.  For typical home shop use, this means one circuit for
    the major power tools, and possibly one for a dust collector or
    shop vac.  Use at least 12 gauge wire -- many power tools have
    big motors, with a big start-up surge.  If you can, use 20 amp
    breakers (NEC), though CEC requires standard 20A receptacles
    which means you'd have to "replug" all your equipment.  Lights
    should either be on a circuit of their own -- and not shared
    with circuits in the rest of the house -- or be on at least two
    separate circuits.  The idea is that you want to avoid a
    situation where a blade is still spinning at several thousand
    RPM, while you're groping in the dark for the OFF switch.

    Do install lots of outlets.  It's easier to install them in the
    beginning, when you don't have to cut into an existing cable.
    It's useful if at least two circuits are accessible at each
    point, so you can run a shop vac or a compressor at the same
    time as the tool you really want.  But use metal boxes and
    plates, and maybe even metal-sheathed cable; you may have
    objects flying around at high speeds if something goes a bit
    wrong.

    Note that some jurisdictions have a "no horizontal wiring"
    rule in workshops or other unfinished areas that are used
    for working.  What this means is that all wiring must be
    run along structural members.  Ie: stapled to studs.

    Other possible shop circuits include heater circuits, 220V
    circuits for some large tools, and air compressor circuits.
    Don't overload circuits, and don't use extension cords if you
    can help it, unless they're rated for high currents.  (A coiled
    extension cord is not as safe as a straight length of wire of
    the same gauge.  Also, the insulation won't withstand as much
    heat, and heat dissipation is the critical issue.)

    If your shop is located at some remove from your main panel,
    you should probably install a subpanel, and derive your shop
    wiring from it.  If you have young children, you may want to
    equip this panel with a cut-off switch, and possibly a lock.
    If you want to install individual switches to ``safe''
    particular circuits, make sure you get ones rated high enough.
    For example, ordinary light switches are not safely able to
    handle the start-up surge generated by a table saw.  Buy
    ``horsepower-rated'' switches instead.

    Finally, note that most home shops are in garages or unfinished
    basements; hence the NEC requirements for GFCIs apply.  And
    even if you ``know'' that you'd never use one of your shop
    outlets to run a lawn mower, the next owner of your house might
    have a different idea.

    Note: Fine Woodworking magazine often carries articles on shop
    wiring.  April 1992 is one place to start.

------------------------------
Subject: Doorbell/telephone/cable other service wiring hints.

    Auxiliary services, such as cable, telephone, doorbell, furnace
    control circuits etc. are generally considered to be "class 2"
    wiring by both the CEC and NEC.

    What this generally means is:

        1) class 2 and house power should not share conduit or
           termination boxes.
        2) class 2 and house power should be 12" apart in walls
           except where necessary.
        3) cross-over should be at 90 degrees.

    While the above may not be strictly necessary to the code, it
    is advantageous anyways - paralleling house power beside telephone
    lines tends to induce hum into the telephone.  Or could interfere
    with fancier furnace control systems.

    With telephone wiring, twisted pair can alleviate these problems,
    and there are new cable types that combine multiple services into
    one sheath.  Consult your inspector if you really want to violate
    the above recommendations.

------------------------------
Subject: Underground Wiring

    You will need to prepare a trench to specifications, use
    special wire, protect the wire with conduit or special plastic
    tubing and possibly lumber (don't use creosoted lumber, it rots
    thermoplastic insulation and acts as a catalyst in the corrosion
    of lead).  The transition from in-house to underground wire is
    generally via conduit.  All outdoor boxes must be specifically
    listed for the purpose, and contain the appropriate gaskets,
    fittings, etc.  If the location of the box is subject to immersion
    in water, a more serious style of water-proof box is needed.  And
    of course, don't forget the GFCIs.

    The required depths and other details vary from jurisdiction to
    jurisdiction, so we suggest you consult your inspector about
    your specific situation.

    A hint: buy a roll of bright yellow tape that says "buried power
    line" and bury it a few inches above where the wire has been placed.

------------------------------
Subject: Aluminum wiring

    During the 1970's, aluminum (instead of copper) wiring became
    quite popular and was extensively used.  Since that time,
    aluminum wiring has been implicated in a number of house fires,
    and most jurisdictions no longer permit it in new installations.
    We recommend, even if you're allowed to, that do not use it for new
    wiring.

    But don't panic if your house has aluminum wiring.  Aluminum
    wiring, when properly installed, can be just as safe as copper.
    Aluminum wiring is, however, very unforgiving of improper
    installation.  We will cover a bit of the theory behind potential
    problems, and what you can do to make your wiring safe.

    The main problem with aluminum wiring is a phenomenon known as
    "cold creep".  When aluminum wiring warms up, it expands.  When
    it cools down, it contracts.  Unlike copper, when aluminum goes
    through a number of warm/cool cycles it loses a bit of tightness each
    time.  To make the problem worse, aluminum oxidises, or corrodes
    when in contact with certain types of metal, so the resistance
    of the connection goes up.  Which causes it to heat up and corrode/
    oxidize still more.  Eventually the wire may start getting very hot,
    melt the insulation or fixture it's attached to, and possibly even
    cause a fire.

    Since people usually encounter aluminum wiring when they move
    into a house built during the 70's, we will cover basic points
    of safe aluminum wiring.  We suggest that, if you're
    considering purchasing a home with aluminum wiring, or have
    discovered it later, that you hire a licensed electrician or
    inspector to check over the wiring for the following things:

        1) Fixtures (eg: outlets and switches) directly attached to
           aluminum wiring should be rated for it.  The device will
           be stamped with "Al/Cu" or "CO/ALR".  The latter supersedes
           the former, but both are safe.   These fixtures are somewhat
           more expensive than the ordinary ones.

        2) Wires should be properly connected (at least 3/4 way around
           the screw in a clockwise direction).  Connections should be
           tight.  While repeated tightening of the screws can make the
           problem worse, during the inspection it would pay off to snug
           up each connection.

           Note that aluminum wiring is still often used for the
           main service entrance cable.  It should be inspected.

        3) "push-in" terminals are an extreme hazard with aluminum wire.
           Any connections using push-in terminals should be redone with
           the proper screw connections immediately.

        4) There should be no signs of overheating: darkened connections,
           melted insulation, or "baked" fixtures.  Any such damage should
           be repaired.

        5) Connections between aluminum and copper wire need to be
           handled specially.  Current Canadian codes require that the
           wire nut used must be specially marked for connecting
           aluminum to copper.  The NEC requires that the wire be
           connected together using special crimp devices, with an
           anti-oxidant grease.  The tools and materials for the latter
           are quite expensive - not practical to do it yourself unless
           you can rent the tool.

        6) Any non-rated receptacle can be connected to aluminum wiring
           by means of a short copper "pigtail".  See (5) above.

        7) Shows reasonable workmanship: neat wiring, properly stripped
           (not nicked) wire etc.

    If, when considering purchasing a home, an inspection of the wiring
    shows no problems or only one or two, we believe that you can consider
    the wiring safe.  If there are signs of problems in many places,
    we suggest you look elsewhere.  If the wrong receptacles are used,
    you can replace them with the proper type, or use pigtails - having
    this professionally done can range from $3 to $10 per receptacle/
    switch.  You can do this yourself too.

------------------------------
Subject: I'm buying a house!  What should I do?

    Congratulations.  But...  It's generally a good idea to hire
    an inspector to look through the house for hidden gotchas.
    Not just for wiring, but plumbing and structural as well.  If an
    inspection of the wiring shows no problems or only one or two minor
    ones, we believe that you can consider the wiring safe (after any
    minor problems are fixed).  If there are signs of problems in many
    places, we suggest you look elsewhere.

    Here's some hints on what to look for:

    Obvious non-code wiring can include:

        - Zip cord wiring, either concealed or nailed to walls
        - Hot wiring on the identified (neutral) conductor without
          proper marking.
        - Ungrounded grounding outlets (except when downstream of
          a GFCI)
        - Splices hanging in mid-air (other than proper knob-and-tube)
        - Switched neutrals
        - Unsecured Romex swinging about like grapevines

    Certain wiring practices that are actually to code (or were at one
    time) sometimes reveal DIY wiring that may have hidden violations:

        - Switches that seem to control nothing (abandoned, perhaps
           not properly terminated wiring)
        - A wall switch that controls things that you think it
          shouldn't, for instance mysteriously removing power
          from lights or outlets in other rooms.
        - Switches and outlets in bizarre locations
        - Great numbers of junction boxes without outlets or lamps
        - Junction boxes with great numbers of wires going into them
        - Wiring that passes through a closet instead of a wall or
          ceiling
        - Backwrapped grounding wires (ground wire wrapped around
          the incoming cable insulation outside the box).
        - A breaker or fuse for outside wiring that is near the bottom
          of the breaker panel or in an add-on fusebox.  The outdoor
          wiring may have been homeowner-installed after the house was
          built, and was not buried deep enough or was done with the
          wrong kind of wire.

------------------------------
Subject: What is this weird stuff?  Old style wiring

    In the years since Edison "invented" electricity, several different
    wiring "styles" have come and gone.  When you buy an older home you
    may encounter some of this stuff.  This section describes the old
    methods, and some of their idiosyncrasies.

    The oldest wiring system you're likely to encounter is called
    "knob and tube" (K&T).  It is made up of individual conductors with
    a cloth insulation.  The wires are run along side structural
    members (eg: joists or studs) using ceramic stand-offs (knobs).
    Wire is run through structural members using ceramic tubes.  Connections
    were made by twisting the wire together, soldering, and wrapping
    with tape.  Since the hot and neutral were run separately,
    the wiring tends to be rather confusing.  A neutral often runs
    down the centre of each room, with "taps" off to each fixture.
    The hot wire tended to run from one fixture to the next.  In some
    cases K&T isn't colour-coded, so the neutral is often the same
    colour as the hot wires.

    You'll see K&T in homes built as late as the 40's.

    Comments on K&T:

        - the people installing K&T were pretty paranoid about
          electricity, so the workmanship tends to be pretty good.
        - The wire, insulation and insulators tend to stand up
          very well.  Most K&T I've seen, for example, is in
          quite good condition.
        - No grounding.  Grounding is usually difficult to install.
        - boxes are small.  Receptacle replacement (particularly with
          GFCI) can be difficult.  No bushing on boxes either,
          so wiring changes need special attention to box entry.
        - Sometimes the neutral isn't balanced very well between
          separately hot circuits, so it is sometimes possible to
          overload the neutral without exceeding the fusing on
          any circuit.
        - In DC days it was common to fuse both sides, and no
          harm was done.  In fact, it was probably a Good Thing.
          The practise apparently carried over to K&T where
          you may find fused neutrals.  This is a very bad
          thing.
        - Building code does not usually permit insulation in
          walls or ceilings that contains K&T.  Some jurisdictions
|          will allow it under some circumstances (eg: engineer's
|          certificate).
        - Connection to existing K&T from new circuits can be
          tricky.  Consult your inspector.
        - Modern wiring practice requires considerably more
          outlets to be installed than K&T systems did.

    Since K&T tends to be in pretty decent condition it generally
    isn't necessary to replace it simply because it's K&T.  What
    you should watch out for is renovations that have interfered
    with it and be cautious about circuit loading.  In many cases
    it's perfectly reasonable to leave existing K&T alone, and add
    new fixtures on new circuits using modern techniques.

    After K&T, they invented multi-conductor cable.  The first type
    you will see is roughly a cloth and varnish insulation.  It
    looks much like the romex cable of the last decade or two.
    This stuff was used in the 40's and 50's.  Again, no grounding
    conductor.  It was installed much like modern wiring.  Its
    major drawback is that this type of insulation embrittles.
    We've seen whole systems where the insulation would fracture
    and fall off at a touch.  BX cable of the same vintage has
    similar problems.  It is possible for the hot conductor to
    short out to the cable jacket.  Since the jacket is rusted, it
    no longer presents a low resistance return path for the current
    flow, but rather more acts like a resistance heater.  In
    extreme cases the cable jacket will become red hot without
    blowing the fuse or circuit breaker.  The best thing to do with
    old style BX is to replace it with modern cable whenever it's
    encountered and there's any hint of the sheath rusting.

    This stuff is very fragile, and becomes rather hazardous if the
    wires become bare.  This wiring should be left untouched as
    much as possible - whenever an opportunity arises, replace it.
    A simple receptacle or switch replacement can turn into a
    several hour long frustrating fight with electrical tape or
    heat-shrink tubing.

    After this wiring technique, the more modern romex was
    invented.  It's almost a asphalt impregnated cloth.  Often a
    bit sticky.  This stuff stands up reasonably well and doesn't
    present a hazard and is reasonably easy to work with.  It does
    not need to be replaced - it should be considered as safe as
    the "modern" stuff - thermoplastic insulation wire.  Just don't
    abuse it too much.

------------------------------
Subject: Where do I buy stuff?

    Try to find a proper electrical supply outlet near you.  Their
    prices will often be considerably better than chain hardware stores or
    DIY centres, have better quality materials, have wider variety
    including the "odd" stuff, and have people behind the counter that
    know what you're talking about.  Cultivate friendly knowledgeable
    sales people.  They'll give you much valuable information.

------------------------------
Subject: Copper wire characteristics table

    These are taken from the Amateur Radio Relay Handbook, 1985.

    AWG  dia    circ  open   cable  ft/lb   ohms/
         mils   mils  air A  Amp    bare    1000'

    10   101.9 10380    55    33    31.82   1.018
    12    80.8  6530    41    23    50.59   1.619
    14    64.1  4107    32    17    80.44   2.575

    We don't show specs for 8ga or larger because they're
    usually stranded.

    Mils are .001".  "open air A" is a continuous rating for
    a single conductor with insulation in open air.  "cable amp"
    is for in multiple conductor cables.  Disregard the amperage
    ratings for household use.

    To calculate voltage drop, plug in the values:

        V = DIR/1000'

    Where I is the amperage, R is from the ohms/1000' column
    above, and D is the total distance the current travels (don't
    forget to add the length of the neutral and hot together - ie:
    usually double cable length).  Design rules in the CEC call
    for a maximum voltage drop of 6% (7V on 120V circuit)

------------------------------
Subject: Smoke detector guidelines
|
|    Many (most?) building codes now require the installation of
|    smoke detectors in homes.  In fact, this has been made
|    retroactive in many municipalities.
|
|    There are many different types of smoke detectors.  Ionization,
|    photo-cell, battery-powered, AC-powered etc.  The only thing
|    we're concerned with here, is AC versus battery powered, other
|    than to comment that most building codes are based around
|    ionization detectors, photocell units being usually for
|    somewhat more specialized purposes.  All things being equal, in
|    a residential setting with the "ordinary fire", an ionization
|    detector will detect smoke before a photo-cell will - indeed,
|    in some fires, the smoke is almost invisible, and less likely
|    to trip a photo-cell.
|
|    There is another type of fire detectors - "heat detectors".
|    These work usually by a small piece of special metal melting at
|    110F or so.  These are much better at avoiding false trips.
|    But they usually take much longer to trip than a smoke detector, and
|    should usually only be considered for triggering sprinkler
|    devices (where the consequences of a false trip are quite
|    severe).  Heat detectors should not be used as primary fire
|    detection.
|
|    Most building codes that mandate detectors mandated AC-powered
|    ones for new construction.  This is because the statistics show
|    that, in houses equipped with smoke detectors, a lot more
|    people were getting killed in houses with battery-only
|    detectors that had dead batteries than were getting killed in
|    houses where the breakers tripped and killed an AC-only
|    detector.  It's also worth noting that some battery detectors
|    are quite sensitive about battery condition.  Some even refuse
|    to work if the battery is zinc-carbon (standard cheap battery)
|    instead of alkaline (more expensive).
|
|    Our building code discourages the installation of smoke
|    detectors on circuits used for other purposes.  This means that
|    only a main-panel breaker trip can kill the detectors.  A
|    main-panel trip is unlikely even in a fire started by an
|    electrical fault until well after the fire has really engulfed the
|       home.
|
|    These codes also usually require that the AC detectors be
|    interconnected so that if one triggers, they all sound the
|    alarm.  This is usually done by an additional wire between the
|    units.
|
|    The above suggests that the best way of doing things is to have
|    one circuit dedicated for smoke detectors, and you run 14-3
|    between each of the detectors - the red wire being the "gang
|    trip" control.
|
|    If you're still concerned about losing power and thereby losing
|    your detectors, we suggest either the use of detectors that run
|    off AC power with battery backup, OR, adding battery detectors
|    into a system that's already adequately covered with AC detectors.
|
|    Battery-only detectors should only be considered a stopgap
|    measure in putting detectors into a house that doesn't have any
|    detectors at all, or adding redundancy into a system that already
|    has AC detectors.
|
|    We also suggest that, if you have battery detectors, you make
|    changing the battery a yearly (or semi-yearly) scheduled event.
|    Some people change the batteries on their birthdays.  Others
|    change the batteries during a "daylight/standard time change"
|    maintenance pass.
|
|    We don't recommend waiting for the detector to tell you that the
|    battery is dead, unless you manually test the detector monthly.
--
Chris Lewis: _Una confibula non sat est_
Phone: Canada 613 832-0541
Latest psroff: FTP://ftp.uunet.ca/distrib/chris_lewis/psroff3.0pl17/*
Latest hp2pbm: FTP://ftp.uunet.ca/distrib/chris_lewis/hp2pbm/*